Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Right here below you will discover a lot of reliable help and advice in relation to How to Install a Bathtub Yourself.
Mounting a tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is conveniently easily accessible, the job can relocate quickly; if you need to open up a wall surface to remove the old tub as well as position the brand-new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as embeded in the new one. Ensure you have actually qualified on your own for the work as well as fit trying it. Instead of working with a professional to take over a halfway-completed job, it is far better to consider employing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will aid you set up a new tub in your shower room if you have currently acquired a brand-new tub and also don't require to change the arrangement of your previous water supply pipelines.
Your tools as well as product checklist ought to consist of the following:
Planning for the Setup
Firstly, the supporting structure provided with the bathroom should be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to prevent stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome as a result of the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, put the tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the tub till the spirit level reviews degree.
To install taps, fit the bottom of the furthest flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water as well as inspect all joints and also new pipework for leakages as well as tighten them if essential. Load the tub and additionally check the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling and sealing around the bathtub needs to wait up until the bath tub has actually been utilized at least once as this will settle it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Secure the faucet in place with the manufacturer given backnut. Once the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type should be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing issues with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components as well as fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to permit the motion experienced when the tub is in use. The sealant can crack relatively early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the market. It is advisable to fit the ceramic tiles using water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that blog post on Installing A Bathtub while doing a search on the internet. Enjoyed our blog entry? Please share it. Help others locate it. Thanks for your time. Kindly check up our blog back soon.
Click Report this page